Executive Summary
Manufacturing a 400 mm-class infrared window is not simply a question of producing a larger optical component. The challenge is maintaining precise surface geometry, parallelism and spectral transmission simultaneously across a large clear aperture.
Astravon has demonstrated this capability through the successful delivery of a CVD zinc sulphide (ZnS) infrared window featuring a 360 mm clear aperture, surface figure of PV ≤ λ/4 and RMS ≤ λ/20 at 10.6 µm, wedge angle ≤30 arcsec, and average transmission of ≥95% across both the 3–5 µm MWIR and 8–12 µm LWIR bands over incidence angles of 0°–10°.
This case study examines the integrated manufacturing processes and verification methods behind these results, illustrating Astravon's production-ready capability in large-format infrared optics.
1. Why Large-Aperture Infrared Windows Are Difficult to Manufacture
Infrared windows serve as critical optical interfaces between sensitive instruments and their operating environments. Their function is not simply to transmit infrared radiation, but to preserve optical performance while accommodating mechanical loads, thermal variations and environmental exposure.
Applications including airborne electro-optical systems, satellite-based infrared payloads, long-range surveillance instruments and advanced scientific observation systems increasingly require apertures substantially larger than those used in conventional infrared assemblies.
As component diameters increase from tens of millimetres to several hundred millimetres, manufacturing complexity rises disproportionately.
Several challenges become particularly significant:
- Surface figure stability: Large, relatively thin substrates are increasingly sensitive to gravitational deflection, fixture-induced deformation, polishing pressure and temperature gradients.
- Material uniformity: Variations in microstructure, residual stress and optical properties become more difficult to manage across the full aperture.
- Surface and subsurface integrity: Brittle infrared materials require carefully controlled material removal to minimise microcracking, grain-boundary damage and scattering defects.
- Coating uniformity: Achieving consistent spectral transmission across a large surface requires precise deposition control, particularly for multilayer infrared coatings.
- Verification: Measurement procedures must distinguish actual component errors from deformation introduced by support conditions and inspection fixtures.
For large-format infrared windows, manufacturing success depends on managing these interactions as a complete engineering problem rather than treating polishing, coating and inspection as independent operations.
2. ZnS as a Material for Large-Format Infrared Optics
Chemical vapour deposition (CVD) zinc sulphide is an established material for infrared optical windows, particularly where transmission in the mid-wave infrared (MWIR) and long-wave infrared (LWIR) regions is required.
ZnS offers several characteristics relevant to demanding optical applications:
- Transmission capability across the 3–5 µm MWIR and 8–12 µm LWIR spectral regions.
- Useful mechanical properties for applications involving vibration and temperature variations.
- Chemical stability and resistance to moisture-related degradation under typical handling conditions.
- Compatibility with anti-reflection coatings designed to improve transmission over selected infrared bands.
However, CVD ZnS is a polycrystalline material. Grain boundaries, local variations in microstructure and residual stresses must be considered when manufacturing large optical components.
As the aperture increases, variations that may be relatively insignificant in smaller windows can become important contributors to scattering, transmitted wavefront degradation and surface deformation.
Residual stress is therefore treated as a manufacturing risk requiring appropriate material acceptance procedures, conditioning and process control. Its actual influence depends on the CVD material, substrate geometry and manufacturing history.
The key engineering objective is to maintain optical uniformity and dimensional stability across the complete usable aperture, not merely to achieve an acceptable finish at selected measurement points.

3. Astravon's Manufacturing Approach
Astravon's large-format ZnS capability integrates material acceptance, staged mechanical processing, precision polishing, infrared coating and final optical verification.
3.1 Material Qualification and Stress Management
Manufacturing control begins with assessment of the incoming CVD ZnS substrate.
Working with upstream material suppliers, the process incorporates inspection of parameters including:
- Spatial transmission uniformity across the substrate.
- Refractive-index homogeneity.
- Residual stress characteristics.
- Material integrity and suitability for subsequent precision processing.
Large-diameter substrates undergo controlled conditioning and stress-management procedures before final optical finishing.
This approach is intended to reduce the risk of dimensional instability during later manufacturing stages, particularly where material removal or coating deposition changes the mechanical stress balance of the component.
3.2 Precision Grinding and Polishing
A 400 mm-diameter substrate with a thickness of just 10 mm presents a substantial manufacturing challenge.
At this geometry, gravity, localised support forces and polishing pressure can influence the apparent and actual surface figure.
Astravon's manufacturing process addresses these effects through staged grinding and polishing operations, using progressively finer material-removal processes to control subsurface damage.
Key process elements include:
Controlled material removal
Coarse grinding, fine grinding and precision polishing are performed sequentially to achieve the required geometry while progressively reducing damage associated with earlier processing stages.
Adaptive polishing pressure
Large-diameter polishing tools and controlled pressure distribution help manage non-uniform removal across the optical surface.
Segmented mechanical support
Purpose-designed support fixtures reduce localised stresses and provide more consistent mechanical conditions during machining and measurement.
Dual-surface geometry correction
Both surfaces are considered during the finishing process to control thickness variation and maintain the required parallelism.
Together, these measures enable the production of large ZnS windows with controlled surface figure and wedge angle across apertures extending into the several-hundred-millimetre range.
3.3 Dual-Band Anti-Reflection Coating
Large-format infrared systems may require high transmission in both MWIR and LWIR bands.
This presents a more demanding coating problem than optimising transmission over a single spectral interval.
Astravon's demonstrated process uses an ion-assisted deposition (IAD) dual-band anti-reflection coating designed for the 3–5 µm and 8–12 µm regions.
The coating approach incorporates deposition-uniformity control and low-stress coating design to manage the interaction between multilayer film properties and substrate geometry.
For relatively thin, large-diameter windows, this is particularly important: coating-induced stress can alter surface figure even when the substrate meets its required optical specification before deposition.
The process therefore includes surface-figure assessment and corrective measures around the coating stage.
The demonstrated coating performance achieves average transmission of at least 95% in each specified infrared band over incidence angles from 0° to 10°.
3.4 Optical Metrology and Verification
Large-format optical manufacturing is only meaningful when performance can be assessed across the specified clear aperture.
Astravon's process chain incorporates interferometric measurement, infrared spectral testing and dedicated parallelism inspection.
Verification activities address:
- Surface figure, including peak-to-valley (PV) and root-mean-square (RMS) error.
- Surface quality and relevant defect criteria.
- Parallelism and wedge angle.
- Spectral transmission in the required infrared bands.
- Geometrical stability through critical manufacturing stages.
The purpose is to establish compliance at the component level rather than relying exclusively on individual process parameters.
4. Manufacturing Case Study: Delivered 400 mm-Class ZnS Infrared Window
A representative production case demonstrates the combined performance of the manufacturing process.
The delivered component was manufactured from a 400 mm-diameter ZnS blank with a 360 mm clear aperture and a nominal thickness of 10 mm.
The usable optical aperture therefore represents 90% of the original blank diameter.
Maintaining the required surface figure over this aperture, while controlling a relatively thin substrate, required coordinated management of mechanical support, polishing conditions and coating-induced deformation.
4.1 Measured Component Specifications
|
Parameter |
Achieved specification |
|---|---|
|
Material |
CVD zinc sulphide (ZnS) |
|
Blank diameter |
Φ400 mm |
|
Clear aperture |
Φ360 mm |
|
Element thickness |
10 mm |
|
Surface figure — PV |
≤ λ/4 at 10.6 µm |
|
Surface figure — RMS |
≤ λ/20 at 10.6 µm |
|
Parallelism / wedge angle |
≤ 30 arcsec |
|
Surface quality |
60-40 scratch-dig, assessed against the applicable Chinese military standard |
|
Coating process |
Ion-assisted deposition (IAD) |
|
Spectral bands |
MWIR: 3–5 µm; LWIR: 8–12 µm |
|
Average spectral transmission |
≥ 95% in each band |
|
Angle of incidence |
0°–10° |
The figures above are reported production results for the representative delivered component. Surface-figure specifications are referenced to the stated 10.6 µm wavelength and apply across the defined clear aperture.
At the specified reference wavelength, the surface-figure limits correspond to approximately 2.65 µm PV and 0.53 µm RMS.
The achieved wedge-angle limit of 30 arcsec is equivalent to 0.5 arcmin, demonstrating sub-arcminute parallelism control over a large optical component.
4.2 Coating Performance Across Two Infrared Bands
The delivered window incorporates a dual-band AR coating designed to maintain high transmission across two distinct infrared regions.
Reported spectrophotometric measurements demonstrate:
- Average transmission ≥ 95% across the 3–5 µm MWIR band.
- Average transmission ≥ 95% across the 8–12 µm LWIR band.
- The specified average transmission maintained over an angle of incidence from 0° to 10°.
These results are supported by batch-production testing, providing evidence of repeatability beyond an initial coating design or laboratory demonstration.
The figures represent band-averaged transmission rather than a guarantee of identical transmission at every individual wavelength.
4.3 Managing Surface Figure Before and After Coating
For large, thin ZnS components, the coating stage introduces an additional mechanical variable.
Even when the substrate meets its specified surface figure following polishing, deposition-induced film stress may influence its final geometry.
In the representative manufacturing case, segmented support tooling and staged surface-figure measurements were incorporated into the process.
Surface-figure compensation and verification before and after coating helped ensure that the final component simultaneously met its geometrical, surface-quality and dual-band transmission requirements.
The significance of this case is the combination of these achieved parameters in a delivered 400 mm-class component, rather than an isolated demonstration of polishing accuracy or optical coating performance.
5. Production-Ready Capability and Application Relevance
The delivered hardware forms part of Astravon's established manufacturing capability for ZnS window components in the 100–400 mm nominal size class.
This capability addresses optical requirements associated with several demanding application areas:
Spaceborne infrared instruments
Large-aperture optical interfaces for infrared payload architectures, subject to mission-specific environmental and qualification requirements.
Airborne and maritime electro-optical systems
Infrared windows for instruments requiring controlled transmission, mechanical robustness and stable optical performance.
Long-range infrared observation
Large optical apertures supporting the collection of infrared radiation in high-sensitivity detection and observation systems.
Scientific and astronomical instrumentation
Custom infrared optical interfaces where aperture size, wavefront preservation and spectral performance are important design considerations.
Advanced laser and beam-control systems
Selected infrared optical applications where substrate transmission, thermal behaviour and coating suitability must be assessed against the operating wavelength and optical power.
In each application, component suitability depends on more than nominal aperture and transmission. Integration constraints, environmental exposure, thermal stability and verification requirements must be evaluated at system level.
The delivered ZnS manufacturing case demonstrates optical component manufacturing capability. It does not, by itself, establish qualification for every space or high-power laser environment.
6. Beyond the Current Manufacturing Baseline
Astravon's current demonstrated capability includes delivered 400 mm-class ZnS windows and a validated manufacturing process encompassing material control, precision machining, dual-band coating and optical verification.
Further development is directed towards increasing manufacturing flexibility and supporting more demanding system requirements.
Areas of continued engineering development include improved uniformity control for large CVD substrates, further reduction of polishing- and coating-induced stresses, refinement of dual-band coating processes, and expanded non-destructive inspection methods for large optical components.
Larger dimensions beyond the established 400 mm class remain a potential development direction rather than a claimed production-ready capability.
This distinction between demonstrated performance and future engineering targets is essential when specifying components for high-reliability optical programmes.
7. Conclusion: Large-Aperture Infrared Optics Require Process-Level Control
The manufacture of large-diameter ZnS infrared windows is fundamentally a problem of integrated precision engineering.
Material uniformity, polishing mechanics, surface quality, coating stress and metrology are interdependent. Optimising any one of these factors in isolation is insufficient to guarantee final optical performance.
Astravon's delivered 400 mm-class ZnS window demonstrates a practical manufacturing solution incorporating:
- A 360 mm clear aperture within a 400 mm-diameter substrate.
- Surface figure controlled to PV ≤ λ/4 and RMS ≤ λ/20 at 10.6 µm.
- Wedge angle limited to 30 arcsec.
- Dual-band AR coating with average transmission ≥ 95% across both MWIR and LWIR bands over 0°–10° incidence.
- Production-validated manufacturing and verification procedures.
For optical system developers, these measured results provide a defined starting point for evaluating large-format infrared windows against programme-specific requirements.
Astravon's engineering focus is to translate demanding optical specifications into manufacturable, measurable and reliably delivered hardware.
Partner with Astravon
Astravon aims to be a trusted engineering partner for optical systems that must perform as intended, throughout their operational life.
